What Probe finds

Intent and behaviour faults, not rule violations.

ERC shows the netlist is consistent. DRC shows the geometry is manufacturable. Neither knows what a pin is for, what a datasheet requires, or whether a component can be bought. Here are the fault types Probe surfaces — expand a card for the example and the chain of evidence behind it.

Blocker

Voltage sequencing & supply faults

A supply that starts in the wrong order, lacks power-good, or is released before it is up.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. PS_POR_B (MPSoC reset) is released ~400 ms after P3V3
  2. Power-good for P0V85, P1V2, P1V8 and VCC_PSPLL are not connected
  3. If a supply drops halfway, the device is partly powered — yet released from reset
Evidence: DS925 p.35 table 37 · CERN #385
Blocker

BOM vs layout

Fitted but unlisted, DNP that is still placed, or the wrong component against what the layout shows.

Example & chain of evidence
Accordion M1
  1. F1 is a 2 A resettable fuse on the supply
  2. R147 (0 Ω) sits in parallel with F1
  3. Current takes the shortcut around the fuse — it protects nothing
Evidence: netlist · R147 ∥ F1
Blocker

Pin function & direction conflict

Two drivers against each other, a floating input, or push-pull driving against open-drain.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. IC4 (SN74AVC2T245) drives PS_SRST_B push-pull via R324 (0 Ω)
  2. IC27 drives the same net with open-drain
  3. With USB connected, both the power-on reset and the PB3 reset are overdriven
Evidence: IC4.B1 · R324 (0 Ω) · IC27 OUT2 (open-drain)
Blocker

Supply shorted or mis-fed

A supply pin and a ground pin on the same net, or a supply fed via the wrong path.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. The net GND gathers both supply and ground pins
  2. IC30.22 (supply) and IC48.3 (ground) end up on the same net
  3. Direct short — ERC doesn't react, both pins get a hot GND
Evidence: netlist · IC30 pin 22, IC48 pin 3
Major

Missing return path / reference plane

A high-speed net that crosses a split in the reference plane without a continuous return path.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. High-speed net changes reference plane at vias
  2. No continuous return path across the plane gap
  3. Return current is forced around — read straight from the copper, several cases
Evidence: layer stack · via position · copper
Major

PDN & decoupling

Decoupling capacitors too far away, in the wrong order, or a regulator without an input capacitor.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. A 60 V buck feeds a supply
  2. No input capacitor near its PVIN pin
  3. The nearest capacitor sits 52.7 mm away
Evidence: component geometry · PVIN net
Major

Off-board coupling & diff pairs

Crosstalk that leaves the board on a connector, or mismatched/incomplete differential pairs.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. ETH_RX_CTL and SLOT2.LVDS_2_N run alongside each other on L7/L8
  2. Noise couples into the LVDS net
  3. The net leaves on J33 — the noise follows it out onto the backplane
Evidence: L7/L8 · SLOT2.LVDS_2_N · connector J33 (1 of 42)
Major

I²C bus without pull-up

An I²C or bus net without a pull-up — or a pull-up too weak for how the net fans out.

Example & chain of evidence
Accordion M1
  1. I²C segment with 10 k pull-ups on each branch
  2. The net fans out to four off-board connectors
  3. Structurally correct — but 10 k is weak for that capacitance
Evidence: I²C net · pull-up value · fan-out
Major

Connectors & mating part

The wrong pin configuration or voltage domain between board and connector, or against the mating part to be connected.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. A module-bus connector carries a supply voltage
  2. A nearby board variant puts a different voltage on the same pin
  3. Intentional — but worth confirming against the mating part
Evidence: pin configuration · voltage domain
Major

Component status & lifecycle

A component that has gone end-of-life, has no stock, or risks being unavailable over the product's lifetime.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. The I²C mux PCA9548APW (NXP)
  2. Distributor catalogue: obsolete, last order date passed 2018-01-24
  3. None in stock, no approved replacement registered
Evidence: BOM · distributor status (NXP)
Minor

Floating & unconnected nets

Nets with only one connection — sometimes an intentional NC, sometimes a floating input that should be driven.

Example & chain of evidence
Method
  1. Probe lists all nets with only one connection
  2. Datasheet-verified NC pins are sorted out as harmless
  3. What remains are inputs that are actually left floating
Evidence: netlist · datasheet NC vs driven input
Minor

Datasheet deviation

A component run outside what the datasheet covers — value, table or load condition.

Example & chain of evidence
DI/OT SB ZU · OHWR0083 R5
  1. IC22 (TPS62125, P2V5) uses a 10 µH inductor
  2. TI's LC table lists only 15 or 22 µH for 1.8–3.3 V
  3. So loop stability is not covered by the datasheet
Evidence: TPS62125 datasheet p.16, table 2

The examples are drawn from published reviews of CERN's DI/OT Zynq UltraScale+ System Board (OHWR0083 R5, CERN-OHL) and E-Sharp's own Accordion M1 board. The list isn't exhaustive — every finding in Probe carries its evidence: net, layer, component and datasheet page.

See them for real

88 CERN designs, 1 351 findings — in the open

We let Probe read 88 designs published on the CERN Open Hardware Repository. Every finding is out in the open, tied to the pins, nets and datasheet pages it rests on.

Find them in your own design.

Book a demo or run a review on an evaluation board. You run the review yourself.

Book a demo of Probe

Show us your board — we review it and go through the findings together.

Prefer to email? info@esharp.se