# E-Sharp > E-Sharp AB (E#) - electronics design and software. Knowledge base for our tools: Probe (design review of board designs), Accordion (modular test systems), Assert (test) and Trace (traceability). This file helps AI assistants navigate our content. Every guide, article and documentation page is also available as plain Markdown via the .md version of its URL. Written in English for machine readability; the pages themselves may be in Swedish. ## Products - [Probe](https://www.esharp.se/probe/): design review of board designs (ODB++) that catches intent and behaviour faults ERC and DRC miss. - [Accordion](https://www.esharp.se/accordion/): modular test systems and modules. - [All products](https://www.esharp.se/produkter/) ## Support - [Support - all products](https://www.esharp.se/support/) - [Probe support](https://www.esharp.se/probe/support/) - [Accordion support](https://www.esharp.se/accordion/support/) - [Probe - security & data handling](https://www.esharp.se/probe/sakerhet/) ## Insights & articles - [Review of CERN's DI/OT Zynq UltraScale+ System Board](https://www.esharp.se/insikter/en/cern-fpga-carrier-board-review.md): An independent, published review of a 14-layer FPGA carrier board — 67 findings, every one cited. The kind of thing ERC and DRC don't see. - [Granskning av CERN:s DI/OT Zynq UltraScale+ System Board](https://www.esharp.se/insikter/fpga-bararkort-case.md): An independent, published review of a 14-layer FPGA carrier board - 67 findings, each cited. The kind ERC and DRC don't catch. - [Vad en granskning hittar som DRC missar](https://www.esharp.se/insikter/drc-vs-granskning.md): The difference between rule violations and design intent, with examples. - [What a review finds that DRC misses](https://www.esharp.se/insikter/en/what-a-review-finds-that-drc-misses.md): ERC and DRC prove a board is legal, not that it's right. Four functional errors that pass every rule check — and why a review is the step that catches them. - [Två sätt att sätta en adress, och båda var monterade](https://www.esharp.se/insikter/bada-alternativen-monterade.md): Ett par nollohmsbryggor låter dig stifta en adresspinne hög eller låg. Det här kortet hade båda monterade på två pinnar — en ren kortslutning som enkelnäts-DRC aldrig kunde se. - [Two ways to set an address, and both of them fitted](https://www.esharp.se/insikter/en/both-options-fitted.md): A pair of zero-ohm links lets you strap an address pin high or low. This board had both fitted on two pins — a dead short the single-net DRC check could never see. - [The formula was right. The number wasn't in the datasheet.](https://www.esharp.se/insikter/en/the-formula-was-right.md): A 1.8 V rail on an AMS1117: the schematic's own arithmetic gives 1.799 V, but it uses an adjust-pin current that isn't in the datasheet. The real rail could sit anywhere from 1.72 V to 2.11 V. - [Twelve volts exactly](https://www.esharp.se/insikter/en/twelve-volts-exactly.md): The feedback divider computes to 12.000 V and the margin looks comfortable. With 5 % resistors the rail can sit 776 mV below the power-good trip — and the BOM never says which resistors are fitted. - [Two boards, both correct, and five volts on a Raspberry Pi](https://www.esharp.se/insikter/en/two-boards-both-correct.md): Each board passed review on its own. Mated, the module's 5 V rail lands on a 3.3 V Raspberry Pi header — a fault that exists only in the connection between them. - [Exakt tolv volt](https://www.esharp.se/insikter/exakt-tolv-volt.md): Spänningsdelaren räknar ut till 12,000 V och marginalen ser bekväm ut. Med 5 %-motstånd kan railen ligga 776 mV under power-good-tröskeln — och BOM:en säger aldrig vilka motstånd som är monterade. - [Formeln stämde. Talet fanns inte i databladet.](https://www.esharp.se/insikter/formeln-stammde.md): En 1,8 V-rail på en AMS1117: schemats egen uträkning ger 1,799 V, men den bygger på en justerpinnsström som inte står i databladet. Den verkliga railen kan hamna var som helst mellan 1,72 V och 2,11 V. - [Två kort, båda rätt, och fem volt på en Raspberry Pi](https://www.esharp.se/insikter/tva-kort-bada-ratt.md): Vart kort klarade granskning för sig. Ihopkopplade landar modulens 5 V-rail på en 3,3 V-stiftlist på en Raspberry Pi — ett fel som bara finns i kopplingen mellan dem. - [Bokstaven som vänder fail-safe](https://www.esharp.se/insikter/bokstaven-som-vander-failsafe.md): Varje symbol, footprint och pinne var rätt. Artikelnumret var en bokstav fel — och den bokstaven håller I²C-bussen låg precis när systemet försöker starta. - [One letter that inverts the fail-safe](https://www.esharp.se/insikter/en/one-letter-fail-safe.md): Every symbol, footprint and pin was correct. The part number was one character off — and that character holds the I²C bus low exactly when the system tries to start. - [AI för designgranskning: få den att bevisa](https://www.esharp.se/insikter/ai-designgranskning.md): The danger of AI in board review isn't that it's wrong, but that you can't see when. Ground every answer in the board. - [Checklista för designgranskning](https://www.esharp.se/insikter/checklista-designgranskning.md): Every experienced designer works to a checklist - memory is no method. A checklist is a prompt to review, not a record of one. - [AI for design review: make it prove it](https://www.esharp.se/insikter/en/ai-for-design-review.md): The danger of AI in board review isn't that it's wrong, but that you can't see when. Ground every answer in the board, and refuse the ones it can't prove. - [A design review checklist](https://www.esharp.se/insikter/en/design-review-checklist.md): Every experienced designer works to a checklist — memory is no method. But a checklist is a prompt for a review, not a record of one. - [ODB++ or Gerber for review](https://www.esharp.se/insikter/en/odb-or-gerber-for-review.md): Gerber is an excellent manufacturing format and a poor review format. The question is which format answers what you're actually asking. - [Review a board without a CAD licence](https://www.esharp.se/insikter/en/review-without-a-cad-licence.md): A review rarely fails on engineering skill, but on what the reviewer is allowed to do with the board. Looking is solved — asking is what's missing. - [Granska ett kort utan CAD-licens](https://www.esharp.se/insikter/granska-utan-cad-licens.md): A review rarely fails on engineering skill, but on what the reviewer may do with the board. Looking is easy; asking is what is missing. - [ODB++ eller Gerber för granskning](https://www.esharp.se/insikter/odb-vs-gerber.md): Gerber is an excellent manufacturing format and a poor review format. The question is which format answers what you are actually asking. - [E-Sharp och Axis tecknar femårigt avtal om testutrustning](https://www.esharp.se/insikter/axis-femarigt-samarbete.md): E-Sharp levererar fler än 200 testsystem till Axis Communications på Accordion-plattformen, i ett femårigt avtal som spänner över utveckling, tillverkning och support. - [E-Sharp and Axis sign a five-year test-equipment agreement](https://www.esharp.se/insikter/en/axis-five-year-partnership.md): E-Sharp will deliver more than 200 test systems to Axis Communications on the Accordion platform, under a five-year agreement spanning development, manufacturing and support. ## About - [About E-Sharp](https://www.esharp.se/om-esharp/) - [Cases](https://www.esharp.se/case/)