Accordion M1 Tone & Power Supply
Generate and analyse line-level audio on the node and power the DUT — all on one networked M1.
- On-module audio generation and analysis, 96 kSps / 24-bit, line level
- 10 SMA jacks (8 inputs in four stereo pairs, 2 outputs) with RGB indication
- Measurements — frequency, V_rms, V_pp, THD, SNR; waveforms sine/square/triangle/noise/sweep
- 2-channel programmable power (Mini-PSU), 5–24 V, 1.5 A per channel
- Lifetime licences for Accordion Pilot and Shell included
Accordion M1 Tone & Power Supply is a ready-made configuration of the compact M1 platform for audio test in PCBA test, NPI and production test. It generates and analyses line-level audio on the device itself and powers the DUT from a 2-channel programmable power module, all on a networked node. All signal processing runs on the Tone Audio module — only settings and results pass to the host. The M.2 slot is free for expansion.
Modules in the configuration
This comes pre-assembled in Accordion M1 Tone & Power Supply — click for the datasheet, specifications and connections.
Specifications, connections & manual
All technical material on the page — expand a section, or download the whole datasheet as a PDF.
Specifications
System
| Parameter | Value | Notes |
|---|---|---|
| Product name | Accordion M1 Tone & Power Supply | |
| Part number | ESH10000755 | |
| Platform | Accordion M1 (mainboard ESH10000597) | |
| Controller | Raspberry Pi 4, 4 GB | |
| Firmware | Accordion 6.0.0 or later | |
| Power input | USB-C (USB-PD) 20 V, via the bundled 130 W power supply | Use the bundled supply only. |
| Input protection | eFuse, 5 A current limit, overvoltage cut-off above 21 V | |
| Network interface | Ethernet, Wifi | |
| Module slots populated | SO-DIMM (Tone Audio Module), N-Top (Tone Audio N-Top), COMTOP (Mini-PSU) | |
| Module slots free | 1× M.2 | |
| Cooling | Active, one fan, speed-regulated by the Accordion process | Full speed at boot. |
| Enclosure | Hammond 1455K1201BU with E# front, top and back panels | |
| Dimensions (L × W × H) | 120 × 78 × 43 mm | |
| Weight | 324 g | |
| Compliance | CE, RoHS, REACH |
Included hardware
| Item | Qty | Notes |
|---|---|---|
| Accordion M1 unit | 1 | Pre-configured with the modules below. |
| ESH10000560 — Tone Audio Module | 1 | SO-DIMM slot. |
| ESH10000612 — Tone Audio N-Top | 1 | N-Top position. |
| ESH10000662 — Mini-PSU | 1 | COMTOP position. |
| microSD card, 32 GB | 1 | Pre-loaded with the Accordion image. |
| USB-C power supply + cable | 1 | 130 W, USB-PD, 1 m cable. |
Lifetime licences for Accordion Shell and Accordion Pilot are included. The Web API, accordionq2 (Python) and AccordionQ2.WebApiClient (.NET) are open clients.
Audio (ESH10000560 via ESH10000612)
| Parameter | Value |
|---|---|
| Sample rate | 96 kSps |
| Sample depth | 24 bit |
| Signal level | Line level |
| Outputs | 2 (left, right), programmable gain per channel |
| Inputs | 8 (four stereo pairs), programmable gain |
| Stereo capture | One pair at a time; left and right sampled simultaneously on two ADC channels |
| Waveforms | Sine, square, triangle, white noise, pink noise, sweep |
| Measurements | Frequency, V_rms, V_pp, THD, SNR |
| Processing | On the module; only settings and results are exchanged with the host |
| Audio connectors | 10 × SMA |
| Indicator LEDs | 24 RGB, software-controlled |
| GPIO | 6 lines, 3.3 V logic (3.6 V absolute maximum) |
Power supply — Mini-PSU (ESH10000662)
| Parameter | Value |
|---|---|
| Channels | 2, independent |
| Output voltage | 5–24 V per channel |
| Output current | 1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V |
| Current-limit accuracy | ±5 mA after two-point calibration (0–1.5 A) |
| Readback | Output voltage and current per channel |
Manual
Hardware
Power-on: connect the bundled USB-C supply and cable, connect Ethernet, apply power (starts at power-up or with the power button, as configured). Boot takes about 1 minute. Audio outputs and the Mini-PSU outputs are off at boot.
Connecting a fixture: SMA cables to the input/output jacks (centre pin = signal, shell = GND); for stereo, connect left to the L jack and right to the R jack of the same pair. GPIO and auxiliary power on the 2×5 header — read the warning under Pinout first. The Mini-PSU output connector carries VOUT1, VOUT2, GND. Power down before changing wiring.
Software
Standard Accordion software — Web API, Pilot, Shell, accordionq2, AccordionQ2.WebApiClient or TestStand.
- Generation: choose output channel, waveform, frequency and gain, then start. The output runs continuously on the module; no samples are streamed from the host.
- Analysis: choose the input pair and gain, start acquisition and read back frequency, V_rms, V_pp, THD or SNR.
- Mini-PSU: set voltage and current limit per channel, then enable.
A browser-based Audio analyser (live readings, spectrum, waterfall, scope) is available in the Accordion Pilot Web UI.
Pinout
Audio jacks (ESH10000612, SMA)
| Jack | Signal | Direction |
|---|---|---|
| J4 | IN1 L | Input |
| J5 | IN1 R | Input |
| J6 | IN2 L | Input |
| J7 | IN2 R | Input |
| J8 | IN3 L | Input |
| J9 | IN3 R | Input |
| J10 | IN4 L | Input |
| J11 | IN4 R | Input |
| J12 | OUT R | Output |
| J13 | OUT L | Output |
GPIO / power header (ESH10000612 J14, 2×5, 2.54 mm)
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | 5V | 2 | VDD (20 V) |
| 3 | MPIO0 | 4 | MPIO3 |
| 5 | MPIO1 | 6 | MPIO4 |
| 7 | MPIO2 | 8 | MPIO5 |
| 9 | GND | 10 | GND |
Warning: pin 2 carries the unit’s 20 V supply. The MPIO pins are 3.3 V logic with a 3.6 V absolute maximum. Connecting pin 2 to any MPIO pin, or to a 5 V or 3.3 V circuit, can damage the module and the DUT. Use pin 2 only for loads rated for 20 V.
Mini-PSU output connector (ESH10000662, 4-pin)
| Pin | Signal |
|---|---|
| 1 | VOUT1 |
| 2 | GND |
| 3 | GND |
| 4 | VOUT2 |
Application notes, cases & news
Insights tagged for this product.
The right Accordion for your bench?
Tell us what you're testing and we'll find the right configuration — or say honestly if a standard setup is enough.