Configuration ESH10000725

Accordion M1 MPIO & Power Supply

Mixed-signal I/O and programmable DUT power in a palm-sized M1 node.

  • 96 mixed-signal channels (MPIO-96) on six 20-pin IDC connectors, one RGB LED per connector
  • 2-channel programmable power (Mini-PSU), 5–24 V, 1.5 A per channel
  • 12-bit ADC/DAC, 0–5 V typical
  • Compact enclosure 120 × 78 × 43 mm, 324 g — Ethernet and WiFi
  • Lifetime licences for Accordion Pilot and Shell included
Price on request
Description

Accordion M1 MPIO & Power Supply is a ready-made configuration of the compact M1 platform for PCBA test, NPI and small-scale production test. It combines 96 reconfigurable mixed-signal channels with a 2-channel programmable power module on a networked node. The M1 main board is based on a Raspberry Pi 4 and comes pre-assembled with MPIO-96, the 6× IDC N-TOP breakout and the Mini-PSU; the M.2 slot is free for expansion.

Use cases
Functional and parametric PCBA test that needs mixed-signal I/O and one or two programmable DUT supplies.
Bring-up benches where channel roles change during test development.
Production fixtures connected via 20-pin IDC ribbon cable.
Technical information

Specifications, connections & manual

All technical material on the page — expand a section, or download the whole datasheet as a PDF.

Specifications

System

Parameter Value Notes
Product name Accordion M1 MPIO & Power Supply
Part number ESH10000725
Platform Accordion M1 (mainboard ESH10000597)
Controller Raspberry Pi 4, 4 GB
Firmware Accordion 6.0.0 or later
Power input USB-C (USB-PD) 20 V, via the bundled 130 W power supply Use the bundled supply only.
Input current, idle ≤ 0.30 A at 20 V (≤ 6 W) PSU outputs off. Tested on every unit.
Input protection eFuse, 5 A current limit, overvoltage cut-off above 21 V
Network interface Ethernet, Wifi
Module slots populated SO-DIMM (MPIO-96), N-Top (IDC breakout), COMTOP (Mini-PSU)
Module slots free 1× M.2
Cooling Active, one fan, speed-regulated by the Accordion process Full speed at boot.
Enclosure Hammond 1455K1201BU with E# front and back panels
Dimensions (L × W × H) 120 × 78 × 43 mm
Weight 324 g
Compliance CE, RoHS, REACH

Included hardware

Item Qty Notes
Accordion M1 unit 1 Pre-configured with the modules below.
ESH10000568 — MPIO-96 SPI Module 1 SO-DIMM slot.
ESH10000355 — 6× IDC N-Top Breakout Module 1 N-Top position.
ESH10000662 — Mini-PSU 1 COMTOP position.
USB-C power supply and cable 1 130 W USB-PD supply with a 1 m USB-C cable.

Lifetime licences for Accordion Shell and Accordion Pilot are included. The Web API, accordionq2 (Python) and AccordionQ2.WebApiClient (.NET) are open clients and need no separate licence.

Channel summary — MPIO-96 (ESH10000568) via IDC (ESH10000355)

Parameter Value
User channels 96, bidirectional
Modes per channel Analog input, analog output, pseudo-digital I/O
ADC / DAC resolution 12-bit / 12-bit
Analog range 0–5 V typical (AD5592R 2× mode)
Pseudo-digital thresholds Programmable VL / VH per channel
Open-drain / floating-output emulation Supported (VH < 0 / VL < 0)
High-speed acquisition Supported, via NumericResult
Max voltage / current at IDC signal pin 5 V / 2 A
IDC pin-1 / pin-2 rails 5 V / 20 V, PTC-fused at 0.25 A per connector
Connector LEDs 1 RGB LED per IDC connector, software-controlled

Power supply — Mini-PSU (ESH10000662)

Parameter Value
Channels 2, independent
Output voltage 5–24 V per channel
Output current 1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V
Current-limit accuracy ±5 mA after two-point calibration (0–1.5 A)
Load transient (0 → 1.5 A) ≤ 1 % overshoot, recovery ≤ 5 µs
Output stability ≤ ±0.1 % over 8 h at 24 V / 1 A
Readback Output voltage and current per channel

Manual

Hardware

Power-on: connect the bundled USB-C supply and the cable to the unit’s power input, connect Ethernet, and apply power (the unit starts at power-up or with the power button, as configured). Boot takes about 1 minute; the fan runs full speed until the Accordion process takes over. The unit is reachable by hostname or DHCP IP. The Mini-PSU outputs are off at boot.

Connecting a fixture: standard 20-pin IDC ribbon from the six connectors to the fixture (check pin-1 orientation); wire the DUT supply leads to the Mini-PSU output connector (VOUT1, VOUT2, GND). Power down before changing wiring.

Software

The unit runs the standard Accordion software — Web API directly, or via Pilot, Shell, accordionq2 (Python), AccordionQ2.WebApiClient (.NET) or TestStand (install commands as for the A2 Lite).

  • MPIO channels: {ModuleIndex}.ESH10000568.MPIO{00–95}, all boot in INPUT mode.
  • The IDC breakout is passive; its pins are addressed through the MPIO channels.
  • Mini-PSU: set voltage and current limit per channel, enable the output, read back output voltage and current.

Pinout

IDC signal connectors (ESH10000355)

Connector Signals MPIO channels
J1 DATA[0–15] MPIO00–MPIO15
J2 DATA[16–31] MPIO16–MPIO31
J3 DATA[32–47] MPIO32–MPIO47
J4 DATA[48–63] MPIO48–MPIO63
J5 DATA[64–79] MPIO64–MPIO79
J6 DATA[80–95] MPIO80–MPIO95

Pin 1 = +5 V, pin 2 = +20 V (both PTC-fused at 0.25 A), pins 3–20 = 16 signals and GND returns.

Mini-PSU output connector (ESH10000662, J2, 4-pin)

Pin Signal
1 VOUT1
2 GND
3 GND
4 VOUT2
Related

Application notes, cases & news

Insights tagged for this product.

The right Accordion for your bench?

Tell us what you're testing and we'll find the right configuration — or say honestly if a standard setup is enough.

Book a demo of Probe

Show us your board — we review it and go through the findings together.

Prefer to email? info@esharp.se